View LTC4002-42_183644.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Final Electrical Specifications
LTC4002-4.2 Standalone Li-Ion Switch Mode Battery Charger
June 2003
FEATURES
s s
DESCRIPTIO
s s s s s s s s s s
s s
Wide Input Supply Range: 4.7V to 24V High Efficiency Current Mode PWM Controller with 500kHz Switching Frequency 1% Charge Voltage Accuracy End-of-Charge Current Detection Output 3 Hour Charge Termination Timer Constant Switching Frequency for Minimum Noise 5% Charge Current Accuracy Low 10A Reverse Battery Drain Current Automatic Battery Recharge Automatic Shutdown When Input Supply is Removed Automatic Trickle Charging of Low Voltage Batteries Battery Temperature Sensing and Charge Qualification Stable with Ceramic Output Capacitor 8-Lead SO and 10-Lead DFN Packages
The LTC(R)4002-4.2 is a complete battery charger controller for single cell 4.2V lithium-ion batteries. With a 500kHz switching frequency, the LTC4002-4.2 provides a small, simple and efficient solution to fast charge Li-Ion batteries from a wide range of supply voltages. An external sense resistor sets the charge current with 5% accuracy. An internal resistor divider and precision reference set the final float voltage to 4.2V with 1% accuracy. When the input supply is removed, the LTC4002-4.2 automatically enters a low current sleep mode, dropping the battery drain current to 10A. An internal comparator detects the near end-of-charge condition while an internal timer sets the total charge time and terminates the charge cycle. After the charge cycle ends, if the battery voltage drops below 4.05V, a new charge cycle will automatically begin. The LTC4002-4.2 is available in the 8-lead SO and 10-lead DFN packages.
, LTC and LT are registered trademarks of Linear Technology Corporation.
APPLICATIO S
s s s
Portable Computers Charging Docks Handheld Instruments
TYPICAL APPLICATIO
VIN 5V TO 24V B330B-13 0.1F CER 2 VCC GATE 2k LTC4002ES8-4.2 CHARGE STATUS 5 7 3 Si6435ADQ B330B-13
90
BAT
10F CER
100
ICHRG = 1.5A RSENSE = 68m (CURVES INCLUDE INPUT DIODE) VBAT = 4V
CHRG
SENSE
EFFICIENCY (%)
L1 6.8H 68m
80
1 0.47F 2.2k
COMP NTC 8 T
BAT GND 4 10k NTC
6 22F CER
+
Li-Ion BATTERY
400242 F01
70
NTC: DALE NTHS-1206N02
60
5
Figure 1. 1.5A Single Cell Li-Ion Battery Charger
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
Efficiency vs Input Voltage
VBAT = 3.8V 10 15 INPUT VOLTAGE (V)
400242 TA02
U
U
20
25
400242i
1
LTC4002-4.2
ABSOLUTE
AXI U RATI GS (Note 1)
Operating Temperature Range (Note 2) .. - 40C to 85C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C
Supply Voltage (VCC) .............................................. 24V GATE .................................................. (VCC - 8V) to VCC BAT, SENSE .............................................. - 0.3V to 14V CHRG, COMP, NTC ..................................... - 0.3V to 8V
PACKAGE/ORDER I FOR ATIO
TOP VIEW COMP VCC GATE PGND SGND 1 2 3 4 5 11 10 NC 9 NTC 8 SENSE 7 BAT 6 CHRG
ORDER PART NUMBER LTC4002EDD-4.2 DD PART MARKING LAGG
COMP 1 VCC 2 GATE 3 GND 4
DD PACKAGE 10-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD IS GND (PIN 11) MUST BE SOLDERED TO PCB
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 10V unless otherwise noted.
SYMBOL VCC ICC PARAMETER VCC Supply Voltage VCC Supply Current Current Mode Shutdown Mode Sleep Mode 5V VCC 24V (Note 2)
q
ELECTRICAL CHARACTERISTICS
CONDITIONS
q
DC Characteristics 4.7 3 3 10 4.168 4.158 93 90 5 2.75 3.9 200 4.2 100 10 2.9 4.2 200 COMP Pin Falling VCC - VBAT VCOMP = 1.2V VCHRG = 1V ICHRG = 1mA VSNS(EOC)/VSNS(CHG) 10 15 360 250 100 25 0.15 25 35 0.3 32 10 500 24 5 5 20 4.232 4.242 107 110 15 3.05 4.5 V mA mA A V V mV mV mV V V mV mV mV A A V % %
400242i
VBAT
Battery Regulated Float Voltage
VSNS(CHG) Constant Current Sense Voltage VSNS(TRKL) Trickle Current Sense Voltage VTRKL VUV VUV VMSD VASD ICOMP ICHRG VCHRG REOC tTIMER Trickle Charge Threshold Voltage VCC Undervoltage Lockout Threshold Voltage VCC Undervoltage Lockout Hysteresis Voltage Manual Shutdown Threshold Voltage Automatic Shutdown Threshold Voltage COMP Pin Output Current CHRG Pin Weak Pull-Down Current CHRG Pin Output Low Voltage End-of-Charge Ratio Charge Time Accuracy
3V VBAT 4V (Note 3) VBAT = 0V (Note 3) VBAT Rising VCC Rising
2
U
U
W
WW U
W
TOP VIEW 8 7 6 5 NTC SENSE BAT CHRG
ORDER PART NUMBER LTC4002ES8-4.2 S8 PART MARKING 400242
S8 PACKAGE 8-LEAD PLASTIC SO TJMAX = 125C, JA = 110C/W
MIN
TYP
MAX
UNITS
0C TA 85C -40C TA 85C
q q
LTC4002-4.2
The q denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 10V unless otherwise noted.
SYMBOL INTC VNTC-HOT PARAMETER NTC Pin Output Current NTC Pin Threshold Voltage (Hot) CONDITIONS VNTC = 0.85V VNTC Falling Hysteresis VNTC Rising Hysteresis VBAT(FULLCHARGED) - VRECHRG, VBAT Falling VCHRG = 8V, Charging Stops 450 500
q q q
ELECTRICAL CHARACTERISTICS
MIN 75 340 2.428 100
TYP 85 355 25 2.465 170 150
MAX 95 370 2.502 200 1 550 100
UNITS A mV mV V mV mV A kHz % ns ns
VNTC-COLD NTC Pin Threshold Voltage (Cold) VRECHRG Recharge Battery Voltage Offset from Full Charged Battery Voltage ILEAK Oscillator fOSC DC Gate Drive tr tf VGATE VGATEHI VGATELO Rise Time Fall Time Output Clamp Voltage Output High Voltage Output Low Voltage Switching Frequency Maximum Duty Cycle CHRG Pin Leakage Current
CGATE = 2000pF, 10% to 90% CGATE = 2000pF, 90% to 10% VCC - VGATE, VCC 9V VGATEHI = VCC - VGATE, VCC 7V VGATELO = VCC - VGATE, VCC 7V
q q q
20 50 8 0.3 4.5
V V V
Note 1: Absolute Maximum Rating are those values beyond which the life of a device may be impaired.
Note 2: The LTC4002-4.2 is tested with Test Circuit 1. Note 3: The LTC4002-4.2 is tested with Test Circuit 2.
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current vs Temperature
4.0
4
3.5
3
fOSC (kHz)
ICC (mA)
ICC (mA)
3.0
2.5 -50 -25
50 25 75 0 TEMPERATURE (C)
UW
100
400242 G01
TA = 25C, VCC = 10V unless otherwise noted. Oscillator Frequency vs Temperature
550
Supply Current vs VCC
CURRENT MODE
500
125
2
5
10
15 VCC (V)
20
25
400242 G02
450 - 50 - 25
0
75 50 25 TEMPERATURE (C)
100
125
400242 G03
400242i
3
LTC4002-4.2 TYPICAL PERFOR A CE CHARACTERISTICS
Oscillator Frequency vs VCC
510
VSNS (mV)
500
VSNS (mV)
fOSC (kHz)
490
5
10
15 VCC (V)
20
Trickle Charge Voltage vs Temperature
3.0 3.0
2.9
2.9
VCHRG (mV)
VTRKL (V)
VTRKL (V)
2.8 - 50 - 25
0
75 50 25 TEMPERATURE (C)
CHRG Pin Output Low Voltage vs Temperature
180 ILOAD = 1mA 29
ICHRG (A)
VCHG (mV)
ICHRG (A)
140
100 - 50 - 25
0
75 50 25 TEMPERATURE (C)
4
UW
400242 G04
TA = 25C, VCC = 10V unless otherwise noted. Current Mode Sense Voltage vs VCC
102 VBAT = 4V
Current Mode Sense Voltage vs Temperature
104 VBAT = 4V
100
100
25
96 - 50 - 25
0
75 50 25 TEMPERATURE (C)
100
125
98
5
10
15 VCC (V)
20
25
400242 G04
400242 G05
Trickle Charge Voltage vs VCC
VBAT = 4V 150
CHRG Pin Output Low Voltage vs VCC
ILOAD = 1mA
140
2.8 100 125
5
10
15 VCC (V)
20
25
400242 G08
130
5
10
15 VCC (V)
20
25
400242 G09
400242 G07
CHRG Pin Weak Pull-Down Current vs Temperature
28
CHRG Output Pin Weak Pull-Down Current vs VCC
VCHRG = 8V
VCHRG = 8V
25
25
100
125
21 - 50 - 25
22
0
75 50 25 TEMPERATURE (C)
100
125
5
10
15 VCC (V)
20
25
400242 G11
400242 G10
400242 G23
400242i
LTC4002-4.2 TYPICAL PERFOR A CE CHARACTERISTICS
Trickle Charge Sense Voltage vs Temperature
10.4 11 VBAT = 2.5V
VSNS (mV)
10.0
10
ICOMP (A)
VSNS (mV)
9.6 - 50 - 25
0
75 50 25 TEMPERATURE (C)
COMP Pin Output Current vs Temperature
104 VCOMP = 0V
ICOMP (A)
INTC (A)
100
85
INTC (A)
96 - 50 - 25
0
75 50 25 TEMPERATURE (C)
Recharge Voltage Offset from Full Charged Voltage vs Temperature
190 160
VRECHRG (mV)
VRECHRG (mV)
150
150
REOC (%)
110 - 50 - 25
0
75 50 25 TEMPERATURE (C)
UW
100
400242 G12
TA = 25C, VCC = 10V unless otherwise noted. COMP Pin Output Current vs VCC
102 VCOMP = 0V
Trickle Charge Sense Voltage vs VCC
VBAT = 2.5V
100
9 125
5
10
15 VCC (V)
20
25
400242 G13
98
5
10
15 VCC (V)
20
25
400242 G14
NTC Pin Output Current vs VCC
86 VNTC = 0V 89
NTC Pin Output Current vs Temperature
VNTC = 0V
85
100
125
84
5
10
15 VCC (V)
20
25
400242 G16
81 - 50 - 25
0
75 50 25 TEMPERATURE (C)
100
125
400242 G15
400242 G17
Recharge Voltage Offset from Full Charged Voltage vs VCC
29
End-of-Charge Ratio vs Temperature
25
140 100 125
5
10
15 VCC (V)
20
25
400242 G19
21 - 50 - 25
0
75 50 25 TEMPERATURE (C)
100
125
400242 G18
400242 G20
400242i
5
LTC4002-4.2 TYPICAL PERFOR A CE CHARACTERISTICS
End-of-Charge Ratio vs VCC
29
4.4
REOC (%)
25
VUV (V)
21 5 10 15 VCC (V) 20 25
400242 G21
PI FU CTIO S
(DFN/SO-8)
COMP (Pin 1/Pin 1): Compensation, Soft-Start and Shutdown Control Pin. The COMP pin is the control signal of the inner loop of the current mode PWM. Charging begins when the COMP pin reaches 800mV. The recommended compensation components are a 0.47F (or larger) capacitor and a 2.2k series resistor. A 100A current into the compensation capacitor also sets the soft-start slew rate. Pulling the COMP pin below 350mV will shut down the charger. VCC (Pin 2/Pin 2): Positive Supply Voltage Input. VCC can range from 4.7V to 24V. A 0.1F or higher capacitor is required at the VCC pin with the lead length kept to a minimum. A 10F low ESR capacitor is also required at the source pins of the power P-channel MOSFET. GATE (Pin 3/Pin 3): Gate Drive Output. Driver Output for the P-Channel MOSFET. The voltage at this pin is internally clamped to 8V below VCC, allowing a low voltage MOSFET with gate-to-source breakdown voltage of 8V or less to be used. PGND, SGND, Exposed Pad, GND (Pins 4, 5, 11/4): IC Ground. CHRG (Pin 6/Pin 5): Open-Drain Charge Status Output. When the battery is being charged, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge current drops to 25% of the full-scale current for more than
6
UW
TA = 25C, VCC = 10V unless otherwise noted.
Undervoltage Lockout Threshold vs Temperature
VCC RISING
4.2
4.0 - 50 - 25
0
75 50 25 TEMPERATURE (C)
100
125
400242 G22
U
U
U
120s, the N-channel MOSFET turns off and a 25A current source is connected from the CHRG pin to GND. When the timer runs out or the input supply is removed, the 25A current source is turned off and the CHRG pin becomes high impedance. BAT (Pin 7/Pin 6): Battery Sense Input. A bypass capacitor of 22F is required to minimize ripple voltage. An internal resistor divider, which is disconnected in sleep mode, sets the final float voltage at this pin. If the battery connection is opened when charging, an overvoltage circuit will limit the charger output voltage to 10% above the programmed float voltage. When VBAT is within 250mV of VCC, the LTC4002-4.2 is forced into sleep mode, dropping ICC to 10A. SENSE (Pin 8/Pin 7): Current Amplifier Sense Input. A sense resistor, RSENSE, must be connected between the SENSE and BAT pins. The maximum charge current is equal to 100mV/RSENSE. NTC (Pin 9/Pin 8): NTC (Negative Temperature Coefficient) Thermistor Input. With an external 10k NTC thermistor to ground, this pin senses the temperature of the battery pack and stops the charger when the temperature is out of range. When the voltage at this pin drops below 350mV at
400242i
LTC4002-4.2
PI FU CTIO S
hot temperature or rises above 2.465V at cold temperature, charging is suspended and the internal timer stops. The CHRG pin output is not affected during this hold state. To
BLOCK DIAGRA
COMP
RSLOP CEOC
RIL
M1
M2
M3 90A
+
CSD 350mV CHRG SD
-
Q4 Q5 25A C/10
GND
+
-
W
U
U
U
(DFN/SO-8)
disable the temperature qualification function, ground the NTC pin. NC (Pin 10/NA): No Connect.
VCC CLK: 100A ISLOP IL DRIVER S Q CPWM R R 20mV GATE
+ -
+-
100mV
SENSE
+
CA
-+
-
BAT
+
VA
-
4.2V
+
CLB
-
2.9V
+
COV UVLO 4.2V
-
4.62V
UV
EOC RQ CRQ
+ -
4.05V
LOGIC
+
STOP TEMP CCOLD NTC_DISABLE
2.465V VCC
-
85A
NTC
-
CHOT
+
350mV
+ -
50mV
400242 BD
400242i
7
LTC4002-4.2
TEST CIRCUITS
Test Circuit 1
15V 1.5V
COMP
100A CA
Test Circuit 2
15V 1.5V
LT1006
0V SENSE COMP 100A CA
VA
LTC4002-4.2
400242 TC02
8
-
+
-
-
+
+
+
0V LTC4002-4.2 SENSE RSENSE 10 VBAT
400242 TC01
-
LT1006 BAT
+
BAT RSENSE 10 1mA 4.2V
400242i
-
LTC4002-4.2
OPERATIO
The LTC4002 is a constant current, constant voltage Li-Ion battery charger controller that uses a current mode PWM step-down (buck) switching architecture. The charge current is set by an external sense resistor (RSENSE) across the SENSE and BAT pins. The final battery float voltage is internally set to 4.2V. For batteries like lithiumion that require accurate final float voltage, the internal 2.465V reference, voltage amplifier and the resistor divider provide regulation with 1% accuracy. A charge cycle begins when the voltage at the VCC pin rises above the UVLO level (4.2V) and is 250mV or more greater than the battery voltage. At the beginning of the charge cycle, if the battery voltage is less than 2.9V, the charger goes into trickle charge mode. The trickle charge current is internally set to 10% of the full-scale current. If the battery voltage stays low for 30 minutes, the battery is considered faulty and the charge cycle is terminated. When the battery voltage exceeds 2.9V, the charger goes into the full-scale constant current charge mode. In constant current mode, the charge current is set by the external sense resistor RSENSE and an internal 100mV reference; IBAT = 100mV/RSENSE. When the battery voltage approaches the programmed float voltage, the charge current will start to decrease.
U
When the current drops to 25% of the full-scale charge current, an internal comparator turns off the internal pulldown N-channel MOSFET at the CHRG pin, and connects a weak current source to ground to indicate a near end-ofcharge condition. An internal 3 hour timer determines the total charge time. After a time out occurs, the charge cycle is terminated and the CHRG pin is forced high impedance. To restart the charge cycle, remove and reapply the input voltage or momentarily shut the charger down. Also, a new charge cycle will begin if the battery voltage drops below the recharge threshold voltage of 4.05V. When the input voltage is present, the charger can be shut down (ICC = 3mA) by pulling the COMP pin low. When the input voltage is not present, the charger goes into sleep mode, dropping ICC to 10A. This will greatly reduce the current drain on the battery and increase the standby time. A 10k NTC (negative temperature coefficient) thermistor can be connected from the NTC pin to ground for battery temperature qualification. The charge cycle is suspended when the temperature is outside of the 0C to 50C window (with DALE NTHS-1206N02).
400242i
9
LTC4002-4.2
APPLICATIO S I FOR ATIO
Undervoltage Lockout (UVLO) An undervoltage lockout circuit monitors the input voltage and keeps the charger off until VCC rises above 4.2V and at least 250mV above the battery voltage. To prevent oscillation around the threshold voltage, the UVLO circuit has 200mV of built-in hysteresis. Trickle Charge and Defective Battery Detection At the beginning of a charge cycle, if the battery voltage is below 2.9V, the charger goes into trickle charge mode with the charge current reduced to 10% of the full-scale current. If the low-battery voltage persists for 30 minutes, the battery is considered defective, the charge cycle is terminated and the CHRG pin is forced to be high impedance. Shutdown The LTC4002 can be shut down by pulling the COMP pin to ground which pulls the GATE pin high and turns off the external P-channel MOSFET. When the COMP pin is released, the internal timer is reset and a new charge cycle starts. In shutdown, the output of the CHRG pin is high impedance and the quiescent current remains at 3mA. Removing the input power supply will put the charger into sleep mode. If the voltage at the VCC pin drops below (VBAT + 250mV) or below the UVLO level (4.2V), the LTC4002-4.2 goes into a low current (ICC = 10A) sleep mode, reducing the battery drain current.
LTC4002-4.2 CHRG
Figure 2. Microprocessor Interface
10
U
CHRG Status Output Pin When a charge cycle starts, the CHRG pin is pulled to ground by an internal N-channel MOSFET which is capable of driving an LED. When the charge current drops to 25% of the full-scale current for more than 120s, the N-channel MOSFET turns off and a weak 25A current source to ground is connected to the CHRG pin. This weak 25A pull-down remains until the timer ends the charge cycle, or the charger is in manual shutdown or sleep mode. After a time out occurs (charge cycle ends), the pin will go into high impedance. By using two different value resistors, a microprocessor can detect three states from this pin (charging, end-of-charge and charging stopped) see Figure 2. To detect the charge mode, force the digital output pin, OUT, high and measure the voltage at the CHRG pin. The N-channel MOSFET will pull the pin low even with a 2k pull-up resistor. Once the charge current drops to 25% of the full-scale current, the N-channel MOSFET is turned off and a 25A current source is connected to the CHRG pin. The IN pin will then be pulled high by the 2k resistor connected to OUT. Now force the OUT pin into a high impedance state, the current source will pull the pin low through the 400k resistor. When the internal timer has expired, the CHRG pin changes to a high impedance state and the 400k resistor will then pull the pin high to indicate the charging has stopped.
VCC VDD 400k 2k PROCESSOR OUT IN
400242 F02
W
UU
400242i
LTC4002-4.2
APPLICATIO S I FOR ATIO
Gate Drive The LTC4002-4.2 gate driver can provide high transient currents to drive the external pass transistor. The rise and fall times are typically 20ns and 50ns respectively when driving a 2000pF load, which is typical for a P-channel MOSFET with RDS(ON) in the range of 50m. A voltage clamp is added to limit the gate drive to 8V below VCC. For example, if VCC is 10V then the GATE output will pull down to 2V max. This allows low voltage P-channel MOSFETs with superior RDS(ON) to be used as the pass transistor thus increasing efficiency. Stability Both the current loop and the voltage loop share a common, high impedance, compensation node (COMP pin). A series capacitor and resistor on this pin compensates both loops. The resistor is included to provide a zero in the loop response and boost the phase margin. The compensation capacitor also provides a soft-start function for the charger. Upon start-up, the COMP pin voltage will quickly rise to 0.05V, due to the 2.2k series resistor, then ramp at a rate set by the internal 100A pullup current source and the external capacitor. Battery charge current starts ramping up when the COMP pin voltage reaches 0.8V and full current is achieved with the COMP pin at 1.3V. With a 0.47F capacitor, time to reach full charge current is about 235ms. Capacitance can be increased up to 1F if a longer start-up time is needed.
U
Automatic Battery Recharge After the 3 hour charge cycle is completed and both the battery and the input power supply (wall adapter) are still connected, a new charge cycle will begin if the battery voltage drops below 4.05V due to self-discharge or external loading. This will keep the battery capacity at more than 80% at all times without manually restarting the charge cycle. Battery Temperature Detection A negative temperature coefficient (NTC) thermistor located close to the battery pack can be used to monitor battery temperature and will not allow charging unless the battery temperature is within an acceptable range. Connect a 10k thermistor (DALE NTHS-1206N02) from the NTC pin to ground. If the temperature rises to 50C, the resistance of the NTC will be approximately 4.1k. With the 85A pull-up current source, the Hot temperature voltage threshold is 350mV. For Cold temperature, the voltage threshold is set at 2.456V which is equal to 0C (RNTC 28.4k) with 85A of pull-up current. If the temperature is outside the window, the GATE pin will be pulled up to VCC and the timer frozen while the output status at the CHRG pin remains the same. The charge cycle begins or resumes once the temperature is within the acceptable range. Short the NTC pin to ground to disable the temperature qualification feature.
400242i
W
UU
11
LTC4002-4.2
APPLICATIO S I FOR ATIO
Input and Output Capacitors Since the input capacitor is assumed to absorb all input switching ripple current in the converter, it must have an adequate ripple current rating. Worst-case RMS ripple current is approximately one-half of output charge current. Actual capacitance value is not critical. Solid tantalum capacitors have a high ripple current rating in a relatively small surface mount package, but caution must be used when tantalum capacitors are used for input bypass. High input surge currents can be created when the adapter is hot-plugged to the charger and solid tantalum capacitors have a known failure mechanism when subjected to very high turn-on surge currents. Selecting the highest possible voltage rating on the capacitor will minimize problems. Consult with the manufacturer before use. The selection of output capacitor COUT is primarily determined by the ESR required to minimize ripple voltage and load step transients. The output ripple VOUT is approximately bounded by:
1 VOUT IL ESR + 8 fOSCCOUT
Since IL increases with input voltage, the output ripple is highest at maximum input voltage. Typically, once the ESR requirement is satisfied, the capacitance is adequate for filtering and has the necessary RMS current rating.
12
U
Switching ripple current splits between the battery and the output capacitor depending on the ESR of the output capacitor and the battery impedance. EMI considerations usually make it desirable to minimize ripple current in the battery leads. Ferrite beads or an inductor may be added to increase battery impedance at the 500kHz switching frequency. If the ESR of the output capacitor is 0.2 and the battery impedance is raised to 4 with a bead or inductor, only 5% of the current ripple will flow in the battery. Design Example As a design example, take a charger with the following specifications: VIN = 5V to 24V, VBAT = 4V nominal, IBAT = 1.5A, fOSC = 500kHz, see Figure 1. First, calculate the SENSE resistor : RSENSE = 100mV/1.5A = 68m Choose the inductor for about 65% ripple current at the maximum VIN:
W
UU
L=
4V 4V 1- = 6.838H (500kHz)(0.65)(1.5A) 24V
Selecting a standard value of 6.8H results in a maximum ripple current of :
IL =
4V 4V 1- = 980.4mA (500kHz)(6.8H) 24V
400242i
LTC4002-4.2
APPLICATIO S I FOR ATIO
Next, choose the P-channel MOSFET. The Si6435ADQ in a TSSOP-8 package with RDS(ON) = 42m (nom), 55m (max) offers a small solution. The maximum power dissipation with VIN = 5V and VBAT = 4V at 50C ambient temperature is:
(1.5A) (55m )(4V) = 0.099 W PD = 5V TJ = 50C + (0.099W)(65C/W) = 56.5C
2
CIN is chosen for an RMS current rating of about 0.8A at 85C. The output capacitor is chosen for an ESR similar to the battery impedance of about 100m. The ripple voltage on the BAT pin is:
IL(MAX) (ESR) 2 (0.98A)(0.1) = 49mV = 2 C1: Taiyo Yuden TMK325BJ106MM C2: Taiyo Yuden JMK325BJ226MM L1: TOKO B952AS-6R8N VOUT(RIPPLE) =
The Schottky diode D2 shown in Figure 1 conducts current when the pass transistor is off. In a low duty cycle case, the current rating should be the same or higher than the charge current. Also it should withstand reverse voltage as high as VIN.
U
Board Layout Suggestions When laying out the printed circuit board, the following considerations should be taken to ensure proper operation of the LTC4002-4.2. GATE pin rise and fall times are 20ns and 50ns respectively (with CGATE = 2000pF). To minimize radiation, the catch diode, pass transistor and the input bypass capacitor traces should be kept as short as possible. The positive side of the input capacitor should be close to the source of the P-channel MOSFET; it provides the AC current to the pass transistor. The connection between the catch diode and the pass transistor should also be kept as short as possible. The SENSE and BAT pins should be connected directly to the sense resistor (Kelvin sensing) for best charge current accuracy. The compensation capacitor connected at the COMP pin should return to the ground pin of the IC or as close to it as possible. This will prevent ground noise from disrupting the loop stability. The ground pin also works as a heat sink, therefore use a generous amount of copper around the ground pin. This is especially important for high VCC and/or high gate capacitance applications.
400242i
W
UU
13
LTC4002-4.2
PACKAGE DESCRIPTIO
3.50 0.05 1.65 0.05 2.15 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS R = 0.115 TYP 6 0.38 0.10 10
PIN 1 TOP MARK (SEE NOTE 5) 5 0.200 REF 0.75 0.05 2.38 0.10 (2 SIDES) 1
NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2). CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED 5. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
14
U
DD Package 10-Lead Plastic DFN (3mm x 3mm)
(Reference LTC DWG # 05-08-1699)
0.675 0.05 3.00 0.10 (4 SIDES) 1.65 0.10 (2 SIDES)
(DD10) DFN 0403
0.25 0.05 0.50 BSC
0.00 - 0.05
BOTTOM VIEW--EXPOSED PAD
400242i
LTC4002-4.2
PACKAGE DESCRIPTIO
.050 BSC 8
.245 MIN
.030 .005 TYP RECOMMENDED SOLDER PAD LAYOUT .010 - .020 x 45 (0.254 - 0.508) .008 - .010 (0.203 - 0.254) 0- 8 TYP
.016 - .050 (0.406 - 1.270) NOTE: 1. DIMENSIONS IN
INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
U
S8 Package 8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.045 .005 .189 - .197 (4.801 - 5.004) NOTE 3 7 6 5 .160 .005 .228 - .244 (5.791 - 6.197) .150 - .157 (3.810 - 3.988) NOTE 3 1 2 3 4 .053 - .069 (1.346 - 1.752) .004 - .010 (0.101 - 0.254) .014 - .019 (0.355 - 0.483) TYP .050 (1.270) BSC
SO8 0303
400242i
15
LTC4002-4.2
TYPICAL APPLICATIO
RELATED PARTS
PART NUMBER LTC1732/LTC4050 LTC1733 DESCRIPTION Constant Voltage/Constant Current Li-Ion Linear Battery Chargers Li-Ion Battery Charger with Termal Regulation COMMENTS Standalone Battery Charger, No uC or Firmware Required, Auto Recharge of Low Battery, 10-Pin MSOP, Input Supply Detection Standalone Charger, Constant-Current/Constant-Voltage/ Constant-Temperature, Integrated MOSFET, No External Sense Resistor or Blocking Diodes Need Only Two External Components, Monitors Charge Current, No Reverse Diode or Sense Resistor Required, 50mA to 700mA Wall Adapter May Be Above or Below Battery Voltage, Standalone, 1-, 2-Cell Li-Ion, Also for Charging NiMH and NiCd Batteries 6V VIN 28V, High Efficiency 90%, VOUT 28V, Digital Interface I/O, Small Inductor 0.35 Internal N-FET Requires No Blocking Diode, Current Limit for Safety Charges from USB Input or AC/DC, 100mA/500mA Up to 1.25A, Thermal Regulation, Fully Integrated Thermal Regulation Prevents Overheating, C/10 Termination, C/10 Indicator Charge Termination Included, ICH 700mA, 8-Lead ThinSOT Package Automatic Switching Between DC Sources, Simplified Load Sharing
LTC1734/LTC1734L LTC1980 LTC4006/LTC4007 LTC4008 LTC4052/LTC1730 LTC4053 LTC4054 LTC4056 LTC4412
SOT-23 Li-Ion Battery Chargers Combination Battery Charger and DC/DC Converter 4A Multiple Cell Li-Ion, NiCd, NiMH, Lead Acid Battery Chargers Integrated Pulse Chargers for a 1-Cell Li-Ion Battery USB Compatible Li-Ion Linear Battery Charger Standalone Linear Li-Ion Battery Charger with Integrated Pass Transistor in ThinSOTTM Standalone SOT-23 Li-Ion Linear Battery Charger Low Loss PowerPath Controller in ThinSOT
TM
PowerPath and ThinSOT are trademarks of Linear Technology Corporation.
16
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 q FAX: (408) 434-0507
q
U
Single Cell 4.2V, 2A Li-Ion Battery Charger
VIN 5V TO 12V 100k 1/2 Si9933ADY 2 VCC GATE 3 1/2 Si9933ADY C1 10F CER 0.1F CER LTC4002ES8-4.2 5 7 RSENSE 50m C2 22F CER L1 6.8H B330-13 CHRG SENSE 1 0.47F 2.2k COMP NTC 8 T 10k NTC BAT GND 4 6
+
Li-Ion BATTERY
400242 TA01
NTC: DALE NTHS-1206N02
400242i LT/TP 0603 1K PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 2003

▲Up To Search▲

Price & Availability of LTC4002-42

	To Download LTC4002-42 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .